Reference: 012-009
Reduction from PCIe x1 to PCIe x16, powered via SATA, Molex, or PCIe 6-pin, is used to connect multiple graphics cards using PCIe x1, primarily used in cryptographic mining, cable length 60 cm.
Reference: 012-113
Brand: Crypto services s.r.o.
Riser lock for PCI-E USB riser module. USB module height 21.7 mm. Ensures firm contact between the PCI-E motherboard slot and the USB riser module.
Reference: 079-220
Brand: Shelly
Shelly 1 is a miniature WiFi switch with firmware for control within the Apple HomeKit, which, thanks to its size, can easily be installed under a switch or socket in a deeper enclosure.
Reference: 012-723
Power cable PCI-e 8 pin female to 2x PCI-e 6 + 2 pin male
Reference: 012-022
Virtual display, HDMI 1.4, DDC, EDID, support up to 4K resolution, use when accessing a remote desktop PC without a connected monitor.
Reference: 012-032
Brand: Crypto services s.r.o.
Attention !! Free shipping over $ 200 does not apply to these designs. Lightweight aluminum frame for 6 - 8 graphics cards, which has a source holder on each side and mounting holes in the middle for mounting an ATX-type motherboard. The frame is ready for modular expansion (can be stacked on top of each other), so it is space-saving, but it is also...
Reference: 080-243
Brand: Shelly
Shelly 2.5 has many uses, either as a double switch for appliances or lights, or for controlling shutters with DC or AC power. With such small dimensions it is a handy helper that easily hides in a smaller space. It can be operated manually or automatically via Apple HomeKit.
Reference: 012-112
Brand: Crypto services s.r.o.
Riser lock for PCI-E USB riser module. USB module height 30mm. Ensures firm contact between the PCI-E motherboard slot and the USB riser module.
Reference: 012-031
Second source switch. Using the SATA power supply or MOLEX connector from the first source, it turns on the second source.
Reference: 012-040
Start button with two LEDs. Easy to setup, just connect the cable into the motherboard, and you can switch on power or reset the motherboard.
RF receiver LED dimmer 2x8A 12-36VDC for CCT dimLED controllers
Warranty on goods for at least 2 years
Free shipping on orders over €200 (EU)
Possibility to return undamaged goods within 14 days
Radio frequency receiver dimmer for CCT LED products. The receiver can be hidden (behind a wall, plasterboard or in a cabinet), direct visibility of the receiver for the controller is not necessary.
The receiver is compatible with all dimLED series CCT controllers
To control multiple circuits, it is necessary to use one receiver for each circuit. Each receiver can be paired with up to 10 different controllers of the dimLED series and thus controlled from several places.
If the power is interrupted and then reconnected (for example, by interrupting the power source), this receiver has a memory of the intensity setting (the intensity of the light will return to the last set).
Input voltage: 12-36VDC
Current load: 2x8A (12V 192W, 24V 384W)
Transmission frequency: 2.4GHz
Range: up to 30m
Number of controllers: Max. 10 pcs can be paired to 1 receiver
Dimensions: 175 x 45 x 27mm
Dimming type: PWM modulation
Memory of last setting after power off: YES
Reference: 194-940
LED remote control eight-channel RGBW 8KRXL, remote RF (radio frequency) control, for RGB and RGBW tapes
Reference: 194-935
RGBW connector click for RGBW LED strips with a width of 10 mm. The size of one cube at the coupling is 19x21mm. Maximum current load 5A.
Reference: 194-1244
Power cable for monochrome LED strip 230V3, LED strip 230V3-120. Cannot be used for RGB LED strip 230V5. Cable length 2 meters. For outdoor use, the connection between the LED strip and the power cable must be sealed with high-quality silicone or glue, for example. 230V3 power cord for 230V3 LED strip and 230V3-120 LED strip
Reference: 194-947
RGB PCB connector L for 10 mm tape. Maximum current load 5A. The corner solder joint fits all profiles.
Reference: 194-944
Connection for LED NEON RGB. Used to connect the NEON RGB LED to the controller. The total length of the connection is 20 cm. A mandrel is also included, which is inserted into the NEON RGB LED and the connection is mounted on it. For outdoor use, it is necessary to seal the joint between the LED strip and the connector, for example with high-quality...
Reference: 194-1433
Brand: T-LED
WiFi converter for controlling all RF receivers of the dimLED series using devices with the IOS and Android operating systems. After installing the app (iOS, Android), you can control the light directly from your phone.
RF receiver LED dimmer 2x8A 12-36VDC for CCT dimLED controllers
