Reference: 012-009
Reduction from PCIe x1 to PCIe x16, powered via SATA, Molex, or PCIe 6-pin, is used to connect multiple graphics cards using PCIe x1, primarily used in cryptographic mining, cable length 60 cm.
Reference: 012-113
Brand: Crypto services s.r.o.
Riser lock for PCI-E USB riser module. USB module height 21.7 mm. Ensures firm contact between the PCI-E motherboard slot and the USB riser module.
Reference: 079-220
Brand: Shelly
Shelly 1 is a miniature WiFi switch with firmware for control within the Apple HomeKit, which, thanks to its size, can easily be installed under a switch or socket in a deeper enclosure.
Reference: 012-723
Power cable PCI-e 8 pin female to 2x PCI-e 6 + 2 pin male
Reference: 012-022
Virtual display, HDMI 1.4, DDC, EDID, support up to 4K resolution, use when accessing a remote desktop PC without a connected monitor.
Reference: 012-032
Brand: Crypto services s.r.o.
Attention !! Free shipping over $ 200 does not apply to these designs. Lightweight aluminum frame for 6 - 8 graphics cards, which has a source holder on each side and mounting holes in the middle for mounting an ATX-type motherboard. The frame is ready for modular expansion (can be stacked on top of each other), so it is space-saving, but it is also...
Reference: 080-243
Brand: Shelly
Shelly 2.5 has many uses, either as a double switch for appliances or lights, or for controlling shutters with DC or AC power. With such small dimensions it is a handy helper that easily hides in a smaller space. It can be operated manually or automatically via Apple HomeKit.
Reference: 012-112
Brand: Crypto services s.r.o.
Riser lock for PCI-E USB riser module. USB module height 30mm. Ensures firm contact between the PCI-E motherboard slot and the USB riser module.
Reference: 012-031
Second source switch. Using the SATA power supply or MOLEX connector from the first source, it turns on the second source.
Reference: 012-040
Start button with two LEDs. Easy to setup, just connect the cable into the motherboard, and you can switch on power or reset the motherboard.
RGBW signal amplifier, 12-24V, 4x6A
Warranty on goods for at least 2 years
Free shipping on orders over €200 (EU)
Possibility to return undamaged goods within 14 days
Four-channel RGBW signal amplifier for RGBW LED strips and modules. It is used to extend the performance of LED drivers beyond their allowable load. (For example, to a controller with a maximum load of 72W, connecting an amplifier will add another 288W. Note, the values do not add up. You can only connect the recommended load to the amplifier.)
Can also be used to amplify the signal of monochrome LED strips.
Use the common + on the input, for the common minus you go through the RGB input terminal block, connect the outputs separately, do not connect each output separately.
Reference: 194-1242
LED strip end cap for LED strip 230V3, LED strip 230V3-120 For outdoor use, it is necessary to seal the joint between the LED strip and the terminals, for example with high-quality silicone or glue. 230V3 terminal is for LED strip 230V3 and LED strip 230V3-120
Reference: 194-937
Coupling with cable for LED RGBW strip with a width of 10 mm. The size of one cube at the coupling is 14x15mm. The length of the connector, including the cable, is 17 cm. Maximum current load 5A.
Reference: 194-955
Brand: Mean Well
Power supply marked LRS-75-24, manufactured by Mean Well. It has a universal input voltage range from 100 V to 240 V. Power supply 75 W with output voltage 24 V. Output current is 3.2 A. Power supply LRS-75-24 can be used, among other things, to power LED strips. The model is also compatible with the Creality 3D printer - CR-10 Max. It has protection...
Reference: 194-1432
Brand: T-LED
RGBCCT RF receiver LED dimmer 5x5A 12-24VDC for RGB+CCT dimLED drivers
Reference: 194-946
Waterproof transparent connector with cable for RGB LED strips. The total length of the coupling is 35 cm.
Reference: 194-945
Waterproof transparent connector with cable for RGB LED strips. The total length of the coupling is 35 cm.
Reference: 194-944
Connection for LED NEON RGB. Used to connect the NEON RGB LED to the controller. The total length of the connection is 20 cm. A mandrel is also included, which is inserted into the NEON RGB LED and the connection is mounted on it. For outdoor use, it is necessary to seal the joint between the LED strip and the connector, for example with high-quality...
Reference: 194-1433
Brand: T-LED
WiFi converter for controlling all RF receivers of the dimLED series using devices with the IOS and Android operating systems. After installing the app (iOS, Android), you can control the light directly from your phone.
RGBW signal amplifier, 12-24V, 4x6A
